新品 Motor Stator Testing System MT-6910 (8 Channel) 場所 台北市, 台湾
新しい
Doubleclick to zoom in
売り手に連絡
追加の写真や情報を依頼する
仕様
- 状態
- 新品
- System
- Benchtop
- Function
- Operate directly on the instrument
- Production traceability management - implementing bar code/label printer/laser engraver
- /
- Store test file sets
- 100 sets (existing instruments)
- Sharing test files between devices
- Unable to share, recreate the file
- Accessing test data
- /
- Uploading test data to a cloud database
- /
- User permission management" or "user access control
- /
- Cpk report
- /
- Customized cpk report according to customer requirements
- /
- Test channel
- 17
- Dcr range
- 0.1mΩ-100kΩ
- Dcr accuracy
- Low Resistance0.1mΩ-1Ω±(0.2%±1mΩ)
- High resistance 1ω-100kω ±0.1%
- High Resistance1Ω-100KΩ±0.1%
- Measuring mode
- 4-Wire
- Ac output voltage
- 100V-5000V
- Ac leakage current
- 0.001mA-10mA
- Ac arcing detection
- Detect gears from 0-9
- Dc output voltage
- 100V-6000V
- Dc leakage current
- 0.001mA-5mA
- Dc arcing detection
- Detect gears from 0-9
- Ir output voltage
- 100V-1000V
- Insulation resistance
- 1-9999MΩ
- Measuring time
- 0.1-99.9s Continuously adjustable
- Voltage accuracy
- ±(3% of setting+5V)
- Impulse voltage (programmable)
- 200V-5000V
- Impulse voltage accuracy
- ±2%
- Total area comparison
- When layer short happened, the loss of power on coil increase, the resonance damping coefficient increase, resonance amplitude decrease, the total area decrease. These are the basic parameters we check layer calculating and comparing the deference of area between golden sample and DUT.Show by percentageAnalysis the power loss by this data.
- Differential area comparison
- Add up the difference between normal wave and DUT wave call “ Area differential”.When layer short happened, the inductance reduce(similar the transformer). The wave phase change and the area differential also change. This will show “fail” on the instrument.However, the parameter might cause deviation because of the deviation of inductance, resonance phase shift. (Silicon steel product such as motor and traditional transformer is not suitable)By calculating and comparing the deference of area between golden sample and DUT. To determine the degree of waveform overlap.Compare the inductance by this.
- Wave comparison
- Set a acceptable wave range, if the DUT’s wave is in this range shows “pass” otherwise, “fail”This parameter can judge both amplitude and phase of resonance wave. This can increase the detection capability of layer short.
- Corona comparison
- In pulse test, the insulation defect will cause discharge and create corona. This function is able to count the times that corona happened base on the degree of deviation.Detect the discharge phenomenon on the coil.
- Flat comparison
- If the layer short happened, the waveform will tremble. Therefore, the instrument will quantize and compared it.
- Inductance ranges
- 0.1nH - 99.999KH
- Test frequency
- 10Hz-200kHz
- Frequency output accuracy
- ±0.01%
- Frequency resolution
- 5 Digits
- Ac drive level
- 10mV to 2Vrms (1m Vrms resolution)
- Basic accuracy
- ±0.1%
- Three-phase inductance balance test
- Comparison ModeThe absolute value of the difference between the two sets of coil inductance The ratio of the absolute value of the difference between the two sets of coil inductance to the standard value The ratio of the absolute value of the difference between the inductance of the two setsof coils and the average value of the measured resistance of the three sets of coils
- Test fixture
- According to the test requirements
- Indicator
- Pass/Fail Screen Diaplay/Sound
- Built-in storage
- Storage of 100 rewritable data sets
- Operation
- Manual, RS-232
- Power supply
- Voltage
- Frequency
- 50/60Hz
- Power consumption
- 300VA
- Environment
- Temperature
- Humidity
- 20-90%RH
- Display
- 6910
- 6505
- 4.3" TFT LCD (480*272)
- 6365
- 3 Kg
- Dimension (w*h*d)
- 6910
- 7605
- 14 Kg
- Weight
- 6910
- Interface
- RS-232
- カテゴリー
- 電気試験装置 場所 台湾
- サブカテゴリ―
- Machinery
- サブカテゴリ― 2
- Motor stator testing system
- リスティングID
- 72958885
説明
Hipot/Leakage Current
Insulation Resistance
Winding Layer short Test
Three-Phase Current Balance Test(Option)
Steering test
Inductance Test
It can test multiple sets of DUTs simultaneously
4-Wire DC Resistance measurement will be more accurate than others
The Impulse/Surge with waveform comparison is a non-destructive analysis
Chinese/English screen could be switched arbitrarily